Leave Your Message
What Is Wafer Butterfly Valve?
Blog
100%

Table of Contents

Wafer butterfly valves act as small, useful quarter-turn tools for stopping and managing flow in pipe setups. These valves sit between two pipe ends. Bolts go through to hold the group together. They do not need screw holes on the valve body.

The build gives a solid seal against pressure from both sides. It stops backward flow in one-way systems.

Table of Contents [Hide]
1 What is wafer type butterfly valve?
2 Types of Wafer Butterfly Valves
3 How Does Wafer Butterfly Valve Work?
4 What is the OS&Y stem used mostly for?
5 How to install a wafer butterfly valve?
6 Conclusion
7 FAQS
8 Partner with a Trusted Wafer Butterfly Valve Manufacturer and Supplier

What is wafer type butterfly valve?

Quick Summary​​​​​​
Wafer butterfly valves keep a simple, light frame with few parts. This boosts low cost and easy hold.
Valve Body
Valve bodies without lugs. They fit tight between ends. Bolts go around the body. They spread weight even. This setup cuts costs compared to lug or end types. It also stops direct pass of pipe load to the valve.
Stem
Setups include one-part or two-part rods. Tough-seat models hide the stem from the flow stuff. This allows cheap, strong stuff.
Disc
The disc controls flow. Center types line the stem with the disc middle.
Seat
Seats use rubber or plastic — EPDM for water mixes, NBR for oil fuels, PTFE for chem stuff, or metal for hot work. Seats make press seals when the disc meets them.

Wafer type butterfly valve (1)

Types of Wafer Butterfly Valves

Concentric wafer butterfly valves
The stem goes through the disc middle. These fit low-push jobs with tough seats. They give cheap shut in water and basic work.

Double Offset Wafer Butterfly Valves
Two stem shifts — one from disc/seat middle, one from hole middle — make a cam move. Less rub grows seat life. It betters flow control.

Triple Offset Wafer Butterfly Valves
Three shifts, plus cone seat shape, end rub in work. Metal-to-metal seal gives tight shut without rubber. It fits hot, high-push, or hard jobs (like steam, fuels).

How Does Wafer Butterfly Valve Work?

Work uses quarter-turn rules. The disc sticks to the stem. It turns 90 degrees. Tough seats give main seal. Stem pack adds back hold. The tools auto turn for far or fast use.

In shut spot, the disc sits across flow. It seals to the seat. In open spot, the disc lines with flow. It blocks little for almost full pass. In control spot, part turn sets amount. Low swirl comes from smooth disc shape.

What Is A Wafer Butterfly Valve Used For?

Wafer butterfly valves manage stop, on/off, and fair control in mid-push systems. 

Water and waste water care
HVAC, area heat, and cold water lines
Chemical and petrochemical work
Sea and ship salt water lines
Fire guard and spray nets
Pressed air, empty, and gas spread

How to install a wafer butterfly valve

Pre-Installation Steps
Clean end faces and pipe. Check valve for harm. Set disc a bit open (5–10°) to guard seat in hold.
Installation Best Practices
Line valve straight with line-up lugs or space bits. Open ends little to skip seat harm. Tighten bolts in cross way to maker turn values. Skip too-tight to stop bend. Turn valve after set to check space and work.
Maintenance Practices
Most tough-seat models need no regular oil. Check seats and pack in shut times. In eat-work, move to PTFE or stainless parts.

Conclusion

Wafer butterfly valves offer flexible, low-cost flow guide with wide field use. Small build, quick work, and fit stuff back many needs.

FAQS

Do wafer butterfly valves support high-pressure service?
What distinguishes wafer from lug and flanged butterfly valves?
Which seat materials suit chemical applications?
Can wafer butterfly valves throttle flow effectively?
Is there a warranty or guarantee?

Partner with a Trusted Valve Manufacturer & Supplier

Field work needing sure wafer butterfly valves wins from join with set manufacturer, supplier, and factory FLUIDO. As a pro sender with custom sets, full rule match, and good price lists, FLUIDO backs jobs with quality sure and tech skill. Reach team at info@fluidovalve.com or vi​a the site for price asks, free bits, or full specs on wafer type butterfly valves and linked field answers.

Blog Tags: